Accel-ppp support next features for control daemon and sessions:
Common available commands for
telnet. Also possible show this help message with one of commands
accel-cmd help and
telnet 127.0.0.1 2000 then run
show stat - shows various statistics information terminate if <interface> [soft|hard]- terminate session by interface name [match] username <username> [soft|hard]- terminate session by username ip <address> [soft|hard]- terminate session by ip address csid <id> [soft|hard]- terminate session by calling station id sid <id> [soft|hard]- terminate session by session id all [soft|hard]- terminate all sessions reload - reload config file restart [hard] - restart daemon hard - restart immediatly default action - terminate all connections then restart shutdown [soft|hard|cancel]- shutdown daemon default action - send termination signals to all clients and wait everybody disconnects soft - wait until all clients disconnects, don't accept new connections hard - shutdown now, don't wait anything cancel - cancel 'shutdown soft' and return to normal operation exit - exit cli show sessions [columns] [order <column>] [match <column> <regexp>] - shows sessions columns: netns - network namespace name ifname - interface name username - user name ip - IP address ip6 - IPv6 address ip6-dp - IPv6 delegated prefix type - VPN type state - state of session uptime - uptime (human readable) uptime-raw - uptime (in seconds) calling-sid - calling station id called-sid - called station id sid - session id comp - compression/encryption method rx-bytes - received bytes (human readable) tx-bytes - transmitted bytes (human readable) rx-bytes-raw - received bytes tx-bytes-raw - transmitted bytes rx-pkts - received packets tx-pkts - transmitted packets ipoe-type - IPoE session type rate-limit - rate limit down-stream/up-stream (Kbit) pppoe mac-filter reload - reload mac-filter file pppoe mac-filter add <address> - add address to mac-filter list pppoe mac-filter del <address> - delete address from mac-filter list pppoe mac-filter show - show current mac-filter list pppoe interface add <name> - start pppoe server on specified interface pppoe interface del <name> - stop pppoe server on specified interface and drop his connections pppoe interface show - show interfaces on which pppoe server started pppoe set verbose <n> - set verbosity of pppoe logging pppoe set PADO-delay <delay[,delay1:count1[,delay2:count2[,...]]]> - set PADO delays (ms) pppoe set Service-Name <name> - set Service-Name to respond pppoe set Service-Name * - respond with client's Service-Name pppoe set AC-Name <name> - set AC-Name tag value pppoe show verbose - show current verbose value pppoe show PADO-delay - show current PADO delay value pppoe show Service-Name - show current Service-Name value pppoe show AC-Name - show current AC-Name tag value shaper change <interface> <value> [temp] - change shaper on specified interface, if temp is set then previous settings may be restored later by 'shaper restore' shaper change all <value> [temp] - change shaper on all interfaces, if temp is set also new interfaces will have specified shaper value shaper restore <interface> - restores shaper settings on specified interface made by 'shaper change' command with 'temp' flag shaper restore all - restores shaper settings on all interfaces made by 'shaper change' command with 'temp' flag
This application is very powerful and often used if you have cli connection. Be default accel-ppp listen TCP port 2000 for input/output with accel-cmd. However telnet has same functions, but accel-cmd is more comfortable, allow send command without enter in to another environment. Detail about cli you may read at [cli] .Let’s revise accel-cmd possible commands.
- accel-cmd show stat - one of more important command, allow display accel-ppp daemon statistics and information about connections types and something counters such as RADIUS auth, acct summary and lost queries. Detail below:
Example, terminate session by username:
echo User-Name=username | radclient -x 127.0.0.1:3799 disconnect testing123.